Ij network scanner selector ex menu12/27/2023 ![]() ![]() Setting for Scanning with MP Navigator EX The scanners selected in the Scan-from-PC Settings screen will be automatically selected in the Scan-from-Operation-Panel Settings screen as well. In that case, you can select one scanner per model. If multiple scanners exist on the network, multiple model names are displayed. In that case, you do not need to select it again. Normally, the MAC address of the machine is already selected after the network setup. The Scan-from-PC Settings screen appears. In the notification area of the taskbar, right-click the IJ Network Scanner Selector EX icon and select Settings. The icon appears in the notification area of the taskbar, and the Scan-from-PC Settings screen appears. If the icon is not displayed in the notification area of the taskbar, from the Start menu, select All Programs > Canon Utilities > IJ Network Scanner Selector EX > IJ Network Scanner Selector EX. If IJ Network Scanner Selector EX is running, its icon appears in the notification area of the taskbar. To scan using the operation panel of the machine, specify the machine with IJ Network Scanner Selector EX.Ĭheck that IJ Network Scanner Selector EX is running. ![]() IJ Network Scanner Selector EX Menu and Setting Screen If the machine is not selected in MP Navigator EX, check that it is selected with IJ Network Scanner Selector EX. The product for scanning using the operation panel also changes. If the product you want to use is changed with IJ Network Scanner Selector EX, the product used for scanning with MP Navigator EX changes as well. By specifying the scanner, you can scan over a network using your computer or the operation panel of the machine. Use IJ Network Scanner Selector EX to specify the scanner you want to use. Multiple users cannot scan at the same time.Ĭomplete the network settings of the machine beforehand using the Setup CD-ROM.Ĭomplete the following settings to enable scanning over a network. You can connect the machine to a network to share it among multiple computers or scan images into a specified computer. ![]() You can scan via USB even if it is not deleted.This article also applies to the PIXMA MX439. You do not need to use this software when scanning via USB. Network communication between the machine and computer is enabled Network settings of the machine is completed after installing the MP Drivers If the machine you want to use is not displayed, check the following conditions and click OK to close the screen, then reopen it and select the machine. Scan-from-Operation-Panel Settings Screenĭisplays when you click Scan-from-Operation-Panel Settings in the Scan-from-PC Settings screen. You can select the scanners from which you want to scan using the operation panel. The Scan-from-Operation-Panel Settings screen appears. If the target model name is not displayed at the top of the Scanners list, from the Start menu, select All Programs > "Canon XXX series Manual" (where "XXX" is the model name) > "Canon XXX series On-screen Manual" (where "XXX" is the model name). When multiple model names are displayed in Scanners, the page for the model at the top of the list appears. MAC addresses of the scanners that can be used over the network are displayed. In the notification area of the taskbar, right-click the icon and select Settings to display the Scan-from-PC Settings screen. The machine must be selected with IJ Network Scanner Selector EX before scanning over a network. (Enabled) disappears from the notification area of the taskbar. You can select the product you want to use.Įxits IJ Network Scanner Selector EX. When you select Disable Canon IJ Network Scanner Selector EX, you will not be able to scan over a network using the operation panel of the machine. If (Enabled) is not displayed in the notification area of the taskbar, from the Start menu, select All Programs > Canon Utilities > IJ Network Scanner Selector EX > IJ Network Scanner Selector EX.ĭisplays when you right-click the IJ Network Scanner Selector EX icon in the notification area of the taskbar.ĭisable Canon IJ Network Scanner Selector EX / Enable Canon IJ Network Scanner Selector EXĮnables or disables IJ Network Scanner Selector EX. When using the computer in a network environment other than the one used to set up the machine, disable IJ Network Scanner Selector EX. ![]() While IJ Network Scanner Selector EX is enabled, it periodically transmits packets to check whether it can communicate with the machine over the network. Set up IJ Network Scanner Selector EX to scan images into a computer over a network using MP Navigator EX or the operation panel of the machine.Īfter installation, IJ Network Scanner Selector EX appears in the notification area of the taskbar. ![]()
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |